Cpap Airsense 10 Autoset Tripack 37453 resmed

Helps one sleep peacefully and fight drowsiness It has an LCD display Adjusts the pressure breath by breath according to the wearer's comfort

Technical Specifications

Units are expressed in cm H2O and hPa. 1 cm H2O is equal to 0.98 hPa

90W Power Supply unit

AC input range	100–240V, 50–60Hz 1.0–1.5A, Class II 115V, 400Hz 1.5A, Class II (nominal for aircraft use)
DC output	24V 3.75A
Typical power consumption	53W (57VA)
Peak power consumption	104W (108VA)

Environmental Conditions

Operating temperature	+5°C to +35°C Note: The air flow for breathing produced by this therapy device can be higher than the temperature of the room. Under extreme ambient temperature conditions (40°C) the device remains safe
Operating humidity	10 to 95% relative humidity, non-condensing
Operating altitude	Sea level to 2,591 m; air pressure range 1013 hPa to 738 hPa
Storage and transport temperature	-20°C to +60°C
Storage and transport humidity	5 to 95% relative humidity, non-condensing

Electromagnetic compatibility

The AirSense 10 complies with all applicable electromagnetic compatibility requirements (EMC) according to IEC60601-1- 2:2007, for residential, commercial and light industry environments. It is recommended that mobile communication devices are kept at least 1 m away from the device. Information regarding the electromagnetic emissions and immunity of this ResMed device can be found on www.resmed.com, on the Products page under Service and Support.

EN 60601-1:2006 classification: Class II (double insulation), Type BF, Ingress protection IP22.

Sensors

Pressure Sensor	Internally located at device outlet, analogue gauge pressure type, -5 to +45 cm H2O (-5 to +45 hPa)
Flow sensor	Internally located at device inlet, digital mass flow type, -70 to +180 L/min

Maximum single fault steady pressure

Device will shut down in the presence of a single fault if the steady state pressure exceeds: 30 cm H2O (30 hPa) for more than 6 sec or 40 cm H2O (40 hPa) for more than 1 sec.

Physical

Dimensions (H x W x D)	116 mm x 205 mm x 150 mm
Air outlet (complies with ISO 5356-1:2004)	22 mm
Weight	1115 g
Housing construction	Flame retardant engineering thermoplastic

Aircraft use

ResMed confirms that device meets the Federal Aviation Administration (FAA) requirements (RTCA/DO-160, section 21, category M) for all phases of air travel.

Air Filter

Standard

Material: Polyester non woven fibre

Average arrestance: >75% for ~7 micron dust

Hypoallergenic

Material: Acrylic and polypropylene fibres in a polypropylene carrier

Efficiency: >98% for ~7-8 micron dust; >80% for ~0.5 micron dust

Wireless module

Technology used: 2G GSM

It is recommended that the device is a minimum distance of 2 cm from the body during operation. Not applicable to masks, tubes or accessories.

Operating pressure range

AutoSet, CPAP: 4 to 20 cm H2O (4 to 20 hPa)

Supplemental oxygen

Maximum flow: 4 L/min

Design Life

Device, power supply unit: 5 years Cleanable water tub: 2.5 years Standard water tub, air tubing: 6 months

- Device

- Air Tubing

- Power Supply Unit

- Travel Bag

- SD Card(already inserted)

General Features

What is the AirSense 10 AutoSet Tripack?

The AirSense 10 AutoSet Tripack is an auto-titrating CPAP machine with a built-in humidifier. It automatically adjusts air pressure to keep your airway open while you sleep.

What are the benefits of the Tripack?
- Auto-adjusting pressure for optimal therapy
- Built-in humidifier for added comfort
- Lightweight and portable design
- Data tracking for monitoring progress (with MyAir app)

Settings and Usage

How do I set up the AirSense 10 AutoSet Tripack?

Your doctor or a respiratory therapist will guide you through setup. Refer to the user manual for detailed instructions.

How does the humidifier work?

The humidifier adds moisture to the air you breathe, making therapy more comfortable.

Can I travel with the AirSense 10 AutoSet Tripack?

Yes, it's compact and lightweight, with universal power compatibility.

Cleaning and Maintenance

How often should I clean the AirSense 10 AutoSet Tripack?

Clean the machine weekly according to the user manual. Wash the water tub and air tubing in warm water with mild detergent.

How do I clean the mask?

Refer to the mask user guide for specific cleaning instructions.

Data and Therapy Monitoring

Does the AirSense 10 AutoSet Tripack track my sleep data?

Yes, it collects therapy data. You can view it on the device or through the MyAir app (sold separately).

What kind of data does it track?

It may track therapy hours, leak rate, AHI (Apnea-Hypopnea Index), and other sleep events.

Troubleshooting

What should I do if my mask leaks?

A small leak is normal. If it's significant, consult your doctor or respiratory therapist to ensure a proper mask fit.

Who should I contact if I have problems with my AirSense 10 AutoSet Tripack?

For troubleshooting or any questions, contact your device provider or ResMed customer support.

Disclaimer: This FAQ is meant to be a general informational resource. Always consult with your doctor to discuss if this is the right fit for you and to get specific instructions for use.